Automatic Multi-Stage Booster Pump 2.2kw


Quiet Running Horizontal Multi-Stage Centrifugal Pump


To work with clean water in domestic applications, irrigation, commercial and light Industrial, Malls, Complexes.

  • Pump body and impellers in stainless steel AISI-304.
  • Motor shaft in stainless steel AISI-420.
  • Diffusers in glass loaded polymer.
  • Suction and discharge mountings in cast iron
  • Mechanical seal in graphite and steatite
  • Motor housing in aluminium L-2521.
  • Asynchronous, two poles.
  • IP 55 protection.


  • POWER: 2.2kw , 220 Volt, 12.5amp
  • Max Flow: 220 l/m
  • Max Rated Flow: 200 l/m
  • Max Head: 61 m
  • Max Pressure: 6.1 Bar
  • Inlet 40mm, Outlet 32mm
  • Pump Activation start-up at 2.5 Bar
  • Complete unit with Electronic Pressure Controller

Price:   R6,900.00 VAT Incl.


Pump & Supply Tank

All Booster Pumps must get there supply from water from a Storage Tank. Booster Pumps cannot simply be put in line with the municipal feed. Please refer to Schematic Drawing of Pump and Tank.

Piping design

Poor piping design and installation is a common cause of poor centrifugal-pump performance or failure. Poor piping can result in:

  • Cavitation
  • Performance dropout
  • Impeller failure
  • Bearing and mechanical seal failures
  • Cracked casings
  • Leaks
  • Spills
  • Fires
Suction piping

Suction piping is more important than discharge piping.

Suction Pipe size and elimination of air pockets

The EEZI-10M has a 1½ inch (40 mm) Inlet. Piping should be at least one nominal pipe size larger than the pump suction Inlet. Velocities should be less than 2 to 3 ft/sec, and the head loss as a result of friction should be less than 1 ft per 100 ft of equivalent piping length.

Suction lines should be short and free of all unnecessary turns. For flooded suctions, piping should be continuously sloping downward to the pump suction so that any vapour pockets can migrate back to the source vessel. For static lifts, the piping should be continuously sloping upward with no air pockets (install gate valves in horizontal position).

If a gate valve is to be install between Pump and Tank it is recommended the pipe size and gate valve be increased to 2½ inch and reduced going into the pump back to 1½ inch. No non-return valves, strainers or filters are to be fitted between Pump and Tank.

The pump already has a non-return valve fitted to it and cannot push back on the Tank. Strainers must be fitted on the pipe work that enters the Tank. Filters can be fitted before entering Tank or on the outlet side of the pump. Make sure that filters can handle the pressure of the pump.

Upstream elbow considerations

When making upstream orientation changes, only long-radius elbows should be used. They should not be connected directly to the pump suction flange, and a minimum of at least two to five pipe diameters of straight pipe should be between the suction flange and the elbow and between successive elbows.

This reduces swirl and turbulence before the fluid reaches the pump. Otherwise, separation of the leading edges may occur, with consequent noisy operation and cavitation damage. The outlet pipe may be reduced to suit the application. Important to remember the smaller the outlet pipe the less volume of water can be pushed.

Cover the Pump

The Pump must be covered and protected from the elements. Pumps incorrectly installed are not covered under the Manufactures Warranty.

Electrical Connection

Electrical Connections to the Pump are to be done by a qualified person.

Our expert installation team will install your pump quickly and professionally.

We can courier your pump to all major towns and cities in South Africa within two to four working days. Email us with your delivery address details, model of pump and we will quote you for pump and delivery accordingly.

Copyright EeziPumps: Water Pressure Booster Pumps


Water Booster Pumps Lazer Park Cnr Malibongwe Dr & Rietvallei Rd.
Cosmo City
Unit 3
77 Roma St.
Cosmo Business Park
Tel. 011 795 2551
Water Booster Pumps Technical Help:
073 161  6249

Water Booster Pumps Sales, Servicing and Installations:
060  578  9338
060  578  9341
Water Booster Pumps email Email Us!


Water Booster Pumps Amanzimtoti Unit 15
Four Tower Business Park
5 Valley View Rd
New Germany
Water Booster Pumps contact 073 161 6249
Water Booster Pumps phone 031 903 4084
Water Booster Pumps email Email Us!

Pump Warranty

See our Warranty here.